Performing a Typical Installation in Console Mode

Install the Event Stream Processor base adapters, the Server, the Studio, and Sybase Control Center for Event Stream Processor in a single process on a single machine.

Prerequisites

If you are installing on Windows 7 and using a sub-capacity license, set the SYBASE_SAM_CAPACITY environment variable in Control Panel > System > Advanced > Environment Variable. Click New for System Variables and enter SYBASE_SAM_CAPACITY as the variable name and PARTITION as the environment value.

Task
  1. From the command line, navigate to the directory where the installation file (setupConsole.exe) resides.
  2. Type setupConsole.exe -i console and press Enter.
  3. When prompted, press Enter to continue.
  4. Select the installation location. To accept the default location, press Enter. To specify a custom location:
    1. Enter an absolute path to the location. Select a file path that does not contain any spaces.
    2. Press Enter.
    3. Type Y or N to indicate whether the location is correct.
      Note: The console accepts both Y and Yes as affirmative, and everything else as a negative response.
    4. If the directory you specified does not exist, the installer asks if you want to create it. Press Y. If the directory already exists, the installer warns you that any software in the folder will be replaced.
      In either case, press Enter to continue.
  5. Enter 1 to select a typical installation, which installs the base adapters, Event Stream Processor Server, the Event Stream Processor Studio, the Sybase Control Center Server for SAP Sybase Event Stream Processor, and the Sybase Control Center Agent for SAP Sybase Event Stream Processor. Press Enter.
    If you have a previous version installed in the selected location, you can either uninstall the previous version, or overwrite it. Enter your selection and press Enter.
  6. Indicate whether to install a licensed version or an evaluation version and press Enter.
    Note: If you install the evaluation version, the software will be active for a 30-day grace period, after which you are prompted for a valid license key. During this grace period, there is no restriction on the number of cores ESP can use. Proceed to step 10.
  7. If you are installing a licensed version, indicate the licensing model you want to use:
    License Type Process
    Specify License Keys
    • Type 1 and press Enter.
    • Specify the absolute path to the license file and press Enter, or press Enter to accept the default.

    If you are using a served license and receive an error that the installer detects a SySAM server already running on your machine, click Previous to return to the SySAM License Entry panel and select the Previously Deployed License Server option.

    If you enter an invalid key, you are prompted by a warning message. You cannot proceed until you enter a valid key or select a different licensing option.
    Previously Deployed License Server
    • Type 2 and press Enter.
    • Press Enter to accept the default host name, or enter the Host Name and Port Number.

    If the license server file is not found, you receive a warning message indicating that the installer cannot verify a license server running on the selected host. When prompted, enter Y to reenter the license server or n to select a different licensing option.
    Continue Without a License Key Type 3 and press Enter. At the prompt asking if you want to continue, press Enter.

    If you continue without a license, the software will be active for a 30-day grace period, after which you are prompted for a valid license key. During this grace period, there is no restriction on the number of cores ESP can use.
  8. Enter the number corresponding to the license type you want to configure. Press Enter.
  9. Indicate whether to configure alerts about SySAM events that may require an administrator's attention. To configure alerts:
    1. Enter Y to indicate that you want to configure alerts.
    2. Enter the SMTP server host that handles your e-mail messages.
    3. Enter the SMTP server port.
    4. Enter the default e-mail address of the person or group from which e-mail messages are sent.
    5. Enter the e-mail addresses of the default recipients.
    6. Enter the default severity level (informational, warning, or error) for e-mail messages.
    Note: To change the SySAM alert settings after installation, edit the lines in the ESP_HOME/sysam/esp_license.prop file:
    • email.smtp.host=smtp
    • email.smtp.port=25
    • email.sender=sender@domain.com
    • email.recipients=user@domain.com
    • email.severity=INFORMATIONAL

    Setting email.severity to NONE disables e-mail alerts, causing all other lines to be ignored. To enable e-mail alerts, set email.severity with ERROR, WARNING, or INFORMATIONAL. Replace SMTP with your SMTP host name, 25 with the port number of your SMTP mail server, sender@domain.com with your e-mail address, and user@domain.com with e-mail recipients. Separate multiple e-mail recipients with a comma (,).

  10. Enter the number corresponding to your geographic location and press Enter.
  11. Read through the license agreement. Press Enter as necessary to move through the text. Stop reading the text at any point by typing back and pressing Enter.
  12. Indicate that you agree to the license terms and press Enter.
  13. Enter an absolute path to the workspace location for Studio projects, or press Enter to accept the default location.
    Note: If you are upgrading from a previous version of Event Stream Processor and want your old projects to remain in the active workspace, enter the path to your existing Studio workspace.
  14. At the preinstallation summary, confirm that you have enough disk space for the installation. Press Enter to continue.
  15. Press Enter to install the files.
  16. Enter a password for the SCC administrator and press Enter. Minimum length is six characters.
  17. Confirm the SCC administrator password and press Enter.
  18. Enter a password for the SCC agent administrator and press Enter. Minimum length is six characters.
  19. Confirm the SCC agent administrator password and press Enter.
  20. When installation is complete, press Enter.
Parent topic: Performing a Typical Installation