Installing Replication Server

Install Replication Server using the setup program.

Prerequisites

Allocate a disk partition of at least 20MB for each Replication Server you are installing. You can add more partitions later, if necessary. Check each partition to make sure it is available and has write permissions.
Allocate the entire partition to the Replication Server. If you allocate only a portion of the partition to Replication Server, you cannot use the remainder for any other purpose.

Task

Verify that the drive on which you install the Replication Server has enough disk space for the components being installed, and at least 100MB of extra disk space for the installation program.
Insert the Replication Server media in the appropriate drive, or download and extract the Replication Server installation image from the Sybase Product Download Center (SPDC).
Launch the setup program.
If the installer does not start automatically, double-click setup.exe or select Start > Run and enter the following, where x: is your CD drive:
```
x:\setup.exe
```
If there is not enough disk space in the temporary disk space directory, set the environment variable TMP to directory_name before running it again, where directory_name is the full path to and name of the temporary directory to which the installation program writes the temporary installation files.
In the Introduction window, click Next.
Indicate where to install Replication Server:
- To select an installation directory, click Choose, and browse for and select the directory.
- To create a new directory, enter a new directory path.
- To restore to the default directory, click Restore Default Folder.
If the installation directory you chose does not exist, you see:
```
The directory directory name does not exist. Do you want to create it?
```
Click Yes.
If the installation directory you selected exists, and already contains an Replication Server installation, you see:
```
Warning: You have chosen to install into an existing
directory. If you proceed with this installation,
any older versions of the products you choose to
install that are detected in this directory will be
replaced.
```
Click Next.
Select the type of installation:
- Typical – installs the default components. This is recommended for most users.
- Full – installs every Replication Server component, including all the supported language modules.
- Custom – lets you select the components to install. Some components are automatically installed if they are required to run your selected components.
Click Next.
Read and agree to the license agreement.
On the Sybase Software Asset Management License Server window, select one of:
- Specify License Keys – click Browse to select the license file. To select multiple license files, use Shift+Click or Ctrl+Click. The license pane displays the license information.
  Alternatively, copy and paste the license information directly in the license pane. Click Next.
  If you specify a served license key, the installer prompts you to install a new SySAM license server. Click:
  - Next to install the new SySAM license server and follow the installation prompts.
  - Previous and select Use previously deployed license server if you have an existing SySAM license server on the same host.
- Use Previously Deployed License Server – for an existing license server, enter the host name of the machine where the license server is running, and the port number if the port number you are using is not default. Click Next.
- Continue installation without a license key – click Next to proceed without any license keys. The installer allows you to install and use the Replication Server components without a license for 30 days. To continue using these components after the end of the grace period, obtain valid licenses from the SPDC, and install these licenses using the Replication Server License Installer.
See the SySAM Users Guide.
Configuring your server for e-mail notification enables designated users to receive information about license management events requiring attention.
Provide:
- SMTP server host name
- SMTP server port number
- E-mail return address
- Recipient e-mail addresses
- Message severity that triggers e-mail messages
Click Next.
The installation summary window displays the selections you have made. Review the information, and click Install.
(Optional) On the Start Sample Replication Server window, select Yes to configure and start a sample Replication Server.

Click Next.
Enter a password from 6-15 characters long. For example:
```
sa_pass
```
This password is used for all Replication Server users when the ERSSD is created.
Click Next.
Write down the information in the Sample RS Summary window, and click Next.
If you chose to configure and start a sample Replication Server, the installer configures and starts the sample Replication Server.
Click Next when done.
When the final window appears, indicating a successful installation, click Done to exit the installer.