Messages on this page are sorted by Sybase error code. Locate the appropriate code for a full description of the message.
Error 1000079 | "IQ SIZE of '%2' for database '%3' is not valid. %1" |
---|---|
Constant | EMSG_HDB_INVALIDDATABASESIZE |
SAP Sybase Error Number | 20739 |
SQL State | QDA79 |
SQL Code | -1000079L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Parameter 2 | requested IQ SIZE |
Parameter 3 | database name |
Probable Cause | The maximum IQ SIZE is 128GB. |
Error 1000082 | "The insert must contain all of the table %2 columns because it participates in one or more joins. %1" |
---|---|
Constant | EMSG_INSRT_MUSTBE_FULLWIDTH |
SAP Sybase Error Number | 20742 |
SQL State | QDA82 |
SQL Code | -1000082L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Parameter 2 | table name |
Probable Cause | If a table participates in a join, then the user cannot load data into that table using a partial width insert. |
Error 1000083 | "The field array entry must be given a name. %1" |
---|---|
Constant | EMSG_HDB_FIELDNONAME |
SAP Sybase Error Number | 20743 |
SQL State | QDA83 |
SQL Code | -1000083L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Probable Cause | This is an internal error. If this error occurs, it should be reported to Sybase. |
Error 1000084 | "The %2th join field array entry for table '%3' must have a name. %1" |
---|---|
Constant | EMSG_HDB_FIELDNOJOINNAME |
SAP Sybase Error Number | 20744 |
SQL State | QDA84 |
SQL Code | -1000084L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Parameter 2 | field array entry |
Parameter 3 | tablename |
Probable Cause | This is an internal error. If this error occurs, it should be reported to Sybase. |
Error 1000085 | "The join field array for table '%2' must have at least one entry. %1" |
---|---|
Constant | EMSG_HDB_FIELDNOJOINNAMES |
SAP Sybase Error Number | 20745 |
SQL State | QDA85 |
SQL Code | -1000085L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Parameter 2 | tablename |
Probable Cause | This an internal error. If this error occurs, it should be reported to Sybase. |
Warning 1000086 | "Length %1 %2%3%4" |
---|---|
Constant | EMSG_PREVIEWFILLERA |
SAP Sybase Error Number | 20746 |
SQL State | QDA86 |
SQL Code | 1000086L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | Parameter 1 description |
Parameter 2 | Parameter 2 description |
Parameter 3 | Parameter 3 description |
Parameter 4 | Parameter 4 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Warning 1000087 | "Delimiter %1 %2%3%4" |
---|---|
Constant | EMSG_PREVIEWFILLERCD |
SAP Sybase Error Number | 20747 |
SQL State | QDA87 |
SQL Code | 1000087L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | delimiter name |
Parameter 2 | Parameter 2 description |
Parameter 3 | Parameter 3 description |
Parameter 4 | Parameter 4 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Warning 1000088 | "Offset %1, Length %2, %3 nulls, %4%5%6 %7" |
---|---|
Constant | EMSG_PREVIEWOFFSET |
SAP Sybase Error Number | 20748 |
SQL State | QDA88 |
SQL Code | 1000088L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | offset |
Parameter 2 | length |
Parameter 3 | nulls |
Parameter 4 | parameter 4 description |
Parameter 5 | parameter 5 description |
Parameter 6 | parameter 6 description |
Parameter 7 | parameter 7 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Warning 1000089 | "Length %1, %2 nulls, %3%4%5 %6" |
---|---|
Constant | EMSG_PREVIEWLENGTH |
SAP Sybase Error Number | 20749 |
SQL State | QDA89 |
SQL Code | 1000089L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | length |
Parameter 2 | nulls |
Parameter 3 | parameter 3 description |
Parameter 4 | parameter 4 description |
Parameter 5 | parameter 5 description |
Parameter 6 | parameter 6 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Warning 1000090 | "%1, %2 nulls, %3%4%5 %6" |
---|---|
Constant | EMSG_PREVIEWPREFIX1 |
SAP Sybase Error Number | 20750 |
SQL State | QDA90 |
SQL Code | 1000090L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | length |
Parameter 2 | nulls |
Parameter 3 | parameter 3 description |
Parameter 4 | parameter 4 description |
Parameter 5 | parameter 5 description |
Parameter 6 | parameter 6 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Warning 1000091 | "%1, %2 nulls, %3%4%5 %6" |
---|---|
Constant | EMSG_PREVIEWPREFIX2 |
SAP Sybase Error Number | 20751 |
SQL State | QDA91 |
SQL Code | 1000091L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | length |
Parameter 2 | nulls |
Parameter 3 | parameter 3 description |
Parameter 4 | parameter 4 description |
Parameter 5 | parameter 5 description |
Parameter 6 | parameter 6 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Error 1000092 | "Table %2 must have a name for the join field array. %1" |
---|---|
Constant | EMSG_HDB_TABLENOJOINNAME |
SAP Sybase Error Number | 20752 |
SQL State | QDA92 |
SQL Code | -1000092L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Parameter 2 | explanation for %2 |
Probable Cause | This is an internal error. If this error occurs, it should be reported to Sybase. |
Warning 1000093 | "%1, %2 nulls, %3%4%5 %6" |
---|---|
Constant | EMSG_PREVIEWPREFIX4 |
SAP Sybase Error Number | 20753 |
SQL State | QDA93 |
SQL Code | 1000093L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | Parameter 1 description |
Parameter 2 | Parameter 2 description |
Parameter 3 | Parameter 3 description |
Parameter 4 | Parameter 4 description |
Parameter 5 | Parameter 5 description |
Parameter 6 | Parameter 6 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Error 1000094 | "Sufficient memory cannot be found for the LOAD. Increasing the Load_Memory_MB or decreasing the BLOCK FACTOR or BLOCK SIZE will allow the LOAD to proceed. %1" |
---|---|
Constant | EMSG_BLOCK_FACTOR_SIZE_LOAD_MEMORY |
SAP Sybase Error Number | 20754 |
SQL State | QDA94 |
SQL Code | -1000094L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | Location of the exception. |
Probable Cause | When the user explicitly sets Load_Memory_MB, the LOAD process applies various heuristics for load parameters in an attempt to find a combination such that the memory required is not more than what the user specified. For a fixed width LOAD, BLOCK FACTOR indicates the minimal number of rows that must be read into memory for each read. The default BLOCK FACTOR is 10,000. Decreasing the BLOCK FACTOR will make the LOAD's internal memory requirements smaller. For a variable length input LOAD, BLOCK SIZE represents the size in bytes in which input data should be read. The default BLOCK SIZE is 500,000 bytes. Decreasing the BLOCK SIZE for a variable width input load will reduce LOAD's memory requirements. Alternatively, the Load_Memory_MB option setting could be raised. |
Warning 1000096 | "Delimiter %1 %2 nulls, %3%4%5 %6" |
---|---|
Constant | EMSG_PREVIEWCD |
SAP Sybase Error Number | 20756 |
SQL State | QDA96 |
SQL Code | 1000096L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | delimiter |
Parameter 2 | nulls |
Parameter 3 | parameter 3 description |
Parameter 4 | parameter 4 description |
Parameter 5 | parameter 5 description |
Parameter 6 | parameter 6 description |
Probable Cause | This is an informational message displayed in context with other messages. |
Error 1000097 | "Parse Error in Command String at '%2'. %1" |
---|---|
Constant | EMSG_PARSEERROR |
SAP Sybase Error Number | 20757 |
SQL State | QDA97 |
SQL Code | -1000097L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Parameter 2 | Start of the parse error |
Probable Cause | Consult the IQ reference manual for the DBCC grammar |
Error 1000099 | "The PAGE SIZE divided by the BLOCK SIZE must be equal to 2, 4, 8, or 16. DATABASE: %2 PAGE SIZE: %3 BLOCK SIZE: %4 %1" |
---|---|
Constant | EMSG_HDB_INVALIDCHUNKSIZE |
SAP Sybase Error Number | 20759 |
SQL State | QDA99 |
SQL Code | -1000099L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Parameter 2 | database name |
Parameter 3 | page size |
Parameter 4 | block size |
Probable Cause | (PAGE SIZE)/(BLOCK SIZE) must be one of 2, 4, 8, 16. Adjust the PAGE SIZE or the BLOCK SIZE in the CREATE DATABASE statement. |
Error 1000100 | "Cannot INSERT, LOAD, or UPDATE a join virtual table. %1" |
---|---|
Constant | EMSG_SQL_NOINSERTJVT |
SAP Sybase Error Number | 20760 |
SQL State | QDB00 |
SQL Code | -1000100L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | location of the exception |
Probable Cause | The user is not allowed to INSERT to or LOAD a join virtual table. Instead you must INSERT to or LOAD the tables which participate in the join and and execute the SYNCHRONIZE command. |
Error 1000101 | "%2 not supported by Sybase IQ. %1" |
---|---|
Constant | EMSG_SQL_STMT_NOTSUPPORTED |
SAP Sybase Error Number | 20761 |
SQL State | QDB01 |
SQL Code | -1000101L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | sql statement type |
Parameter 2 | location of the exception |
Probable Cause | The statement in question is not supported by Sybase IQ. |
Error 1000103 | "Cannot find an index for field '%2'. Every field must have at least one index. Current IndexCount = %3. %1" |
---|---|
Constant | EMSG_CAT_FIELD_HAS_NOINDEX |
SAP Sybase Error Number | 20763 |
SQL State | QDB03 |
SQL Code | -1000103L |
ODBC 2 State | ERROR |
ODBC 3 State | ERROR |
Severity Code | |
Parameter 1 | Field name |
Parameter 2 | Number of indexes found for the named field. |
Parameter 3 | location of the exception |
Probable Cause | This error should not occur during normal operation. Every field in ASIQ will have at least one index (the automatically generated FP index). This error occurs, the operation should be retried. If the error persists, it should be reported to Sybase. Extra information may have been output to the iqmsg file. |