Primary companion resource group

scrgadm -a -t SY.ase -f full-path-of-SY.ase-file

For example:

scrgadm -a -t SY.ase 
-f /sybase/ASE-15_0/SC-3_0/etc/SY.ase

Install the SY.ase resource type only once per cluster. An error message displays if the resource type is already installed.

Create a resource group for the primary companion server. Specify the primary and secondary nodes for the resource group property Nodelist.

scrgadm -a -g resource_group
-y Nodelist=primary-node,secondary-node

For example:

scrgadm -a -g rg_MONEY1 -y Nodelist=node1,node2

scrgadm -a -t SUNW.HAStorage

Create and add the SUNW.HAStorage resource to the Adaptive Server resource group. Specify the file system and device paths on the shared disk that must be relocated to the secondary node in case of fail over:

scrgadm -a -j hastorage_resource_name
-t SUNW.HAStorage
-g resource_group
-x ServicePaths=shared-disk-storage-path

For example:

scrgadm -a -j has_MONEY1 -g rg_MONEY1 
-t SUNW.HAStorage 
-x ServicePaths=/global/node1_share

Create and add the SUNW.LogicalHostname resource to the Adaptive Server resource group. Specify a logical host name that can be relocated to the secondary node in case of fail over.

scrgadm -a -L -j loghost_resource 
-g resource_group 
-l logical_hostname

For example:

scrgadm -a -L -j lh_MONEY1 
-g rg_MONEY1 
-l loghost_node1

The following command creates the Adaptive Server resource and adds it to the resource group:

scrgadm -a -j ase_resource_name -g resource_group \
		-t SY.ase \
		-x Sybase_home=sybase_home_value \
		-x Environment_file=environment_file_path \
		-x Dataserver_name=dataserver_name_value \
		-x Dataserver_login_file=login_file_path \
		-x RUN_server_file=run_server_file_path

For example:

scrgadm -a -j ase_MONEY1 -g rg_MONEY1 \
    -t SY.ase \
    -x Sybase_home=/sybase \
    -x Environment_file=/sybase/SYBASE.sh \
    -x Dataserver_name=MONEY1 \
    -x Dataserver_login_file=/sybase/ASE-15_0/SC-3_0/etc/ase_login_file 
    -x RUN_server_file=/sybase/ASE-15_0/install/RUN_MONEY1

Specify any standard resource property values and extension property values.

You must specify the following three extension property values; otherwise, the command fails: Sybase_home, Dataserver_name, and Dataserver_login_file. You may let other extension properties use default values.

You may configure the following standard resource properties, which are used by the high availability agent fault monitor: Cheap_probe_interval, Thorough_probe_interval, Retry_count, and Retry_interval.

For more information about the standard resource properties, see the Sun Cluster documentation. Table 9-1 describes the extension properties for the Adaptive Server resource.

Establish resource dependency between the SY.ase resource and the SUNW.HAStorage resource. This means the SY.ase resource is online only if the SUNW.HAStorage resource is online, and the SY.ase resource is offline before the SUNW.HAStorage resource is offline:
```
scrgadm -c -j ase_resource_name 
-y Resource_dependencies=hastorage_resource_name
```
For example:
```
scrgadm -c -j ase_MONEY1 
-y Resource_dependencies=has_MONEY1
```
All resources in a resource group implicitly depend on the SUNW.LogocalHostname resource if one is added to the resource group.
For the primary Adaptive Server resource group, execute scswitch to:
- Move the resource group to managed state.
- Enable all resources and their monitors.
- Bring the resource group online on the primary node:
```
scswitch -Z -g resource_group_name
```
  For example:
```
scswitch -Z -g rg_MONEY1
```

See “Using SUNW.HAStoragePlus” to create and add the SUNW.HAStoragePlus resource to the Adaptive Server resource group.